Point de Passage

From Synfig Studio :: Documentation
Jump to: navigation, search
Languages Language: 

English • suomi • français



               Cette page est en cours de traduction, soyez patient ou contribuez !.

Introduction

Les "Points de Passage" sont des symboles graphiques disposés sur le panneau de l'Timetrack. Chaque fois que la valeur d'un paramètre est modifiée en mode édition de l'animation, un Point de Passage vas être créé. For example, when you adjust a "Tangent" Poignée of a vertex in a Spline, a "Waypoint" will be created to note the change. However, you didn't really adjust the tangent, you adjusted the two parameters which define the tangent: its angle ("Theta"), and its length ("Radius"). Opening up the tangent's nodes in the Panneau Paramètres will show that "Waypoints" have been created against each of these 2 parameters.

As a result of adjusting a single "Tangent" Handle, "Waypoint" have been created as follows:

  • the length of the tangent changed ("Radius")
  • the angle of the tangent changed ("Theta")
  • the tangent changed ("Tangent 1")
  • the vertex changed ("Vertex 001")
  • the vertices changes ("Vertices")

Only the first 2 of these are 'leaf waypoints' - the rest are parents (and grandparents, etc) of these 2 waypoints.

As things currently stand, it is only possible to delete one leaf waypoint at a time. If, for example, you want to delete the change made to the "Tangent" Handle above, you'll need to open up the tangent and delete both the "Theta" and "Radius" Waypoints. The ability to delete whole trees of waypoints with a single click would be useful, as would the ability to select multiple waypoints at once, and operate upon them en masse.

Selecting Waypoints

Holding Ctrl allows you to select more than one waypoint for a given valuenode at a time.

  • When nothing is selected, clicking on a point in either normal mode or additive mode will select the time point closest to the click. Subtractive click will do nothing
  • When things are already selected, clicking on a selected point does nothing (in both normal and add mode). Add mode clicking on an unselected point adds it to the set. Normal clicking on an unselected point will select only that one time point. Subtractive clicking on any point will remove it from the the set if it is included.

Normal click out of a waypoint unselect all.

Editing Waypoints

Move it

Waypoints can be dragged left or right with the left mouse button to change the time at which they act upon their parameter(s). If you drag a parent's Waypoint, all its child Waypoints will move with it.

Move some

You can select multiple Waypoints using CtrlClick, and then they can be dragged left or right has moving single waypoint.

More actions

Right-clicking on Waypoint shows a context menu, containing:

  • "Jump to": Set the current time to be the time of the waypoint.
  • "Duplicate": Only appears for single-leaf Waypoints. Creates a copy of the current Waypoint at the currently selected time.
  • "Remove": Only appears for single-leaf waypoints. Deletes the Waypoint.
  • "Remove n Waypoints": Only appears for multi-leaf waypoints. Deletes the n Waypoints.
  • "Edit": Only appears for single-leaf Waypoints.
  TODO: writeme (brings up a dialog allowing various parameters to be set).
  • "Both".: Allows you to change the "In" and "Out" interpolation setting for the Waypoint and all its children.
  • "In".: Allows you to change the "In" interpolation setting for the Waypoint and all its children.
  • "Out".: Allows you to change the "Out" interpolation setting for the Waypoint and all its children.

If the Waypoint is Linked other menu entries related to the link will appear up to those one.

  TODO: writeme (describe added menu entries in case of linked waypoint)

Interpolation

Default Interpolation

The default type of interpolation for new waypoints is defined by a dropdown list at bottom of the Fenêtre Canevas.

It is possible to fix interpolation by parameter. Right-click any parameter and choose its default interpolation from a submenu. The defined interpolation is indicated in the Panneau Paramètres with corresponding icon near the parameter value.

Interpolation In & Out

Each Waypoint has an "In" and an "Out" interpolation setting, which determines the manner in which its parameter changes - whether it changes linearly over time, or follows a curve.

The "In" interpolation defines how the parameter changes in the moments before the Waypoint is reached, and "Out" defines how it changes in the moments after the Waypoint. Available interpolation types are as follows:

  • TCB Smooth: If you imagine a graph of the parameter's value against time, using the TCB interpolation type will fit a smooth curve between adjacent waypoints, much like the Outil Spline fits smooth curves between adjacent spline vertices.
  • Clamped: Acts like TCB interpolation, but never "overshoots" (or "undershoots") the values you set in the Panneau Paramètres.
  • Constant: Stops the animation.
  • Ease In/Out: The graph is horizontal as it leaves the Waypoint.
  • Linear: The graph of parameter value against time is a straight line.
  • Undefined: This is only shown for multi-leaf Waypoints, where there is more than one different interpolation type amongst its leaf Waypoints.

Graphical Representation

The color and shape of the Waypoint as displayed in the Timetrack indicates its interpolation type:

Each Waypoint is split into two halves. The left half indicates its "In" interpolation and the right half indicates its "Out" interpolation, so many different combinations are possible:

Image:Waypoint-combos.png

In the chart above the "In" interpolation is shown on the left, and the "Out" interpolation is shown across the top.

Note: the .sif file used to generate these screenshots is available. File:Waypoint-examples.sif

Here is an File:Interpolation.sif showing 25 different blobs, and how they move with different combinations of Waypoints. It renders to a [voir lien page anglaise 634K .avi file], and is available in lower resolution [voir lien page anglaise]. Notice how:

  • the blobs with any red (Constant) on them don't move at all
  • the yellow (Linear) sides of blobs 'bounce' off the walls
  • the cyan (Ease) sides slow gracefully to a halt at the walls
  • the green (TCB Smooth) sides bounce at the top (the animation is a single down-and-up animation, looped, so there's no 'context' at the top for the TCB to fit the curve to) but act smoothly at the bottom

The 'undefined' (grey) symbol is used when the row in the Time Track Panel represents multiple Waypoints. For example, the 'vertices' row represents all the vertices making up a Spline. Each of those vertices can have multiple Waypoints, each with different interpolations. If all the interpolations are the same, that interpolation's symbol will be used. Otherwise, the grey 'undefined' symbol is used.

Look at the Waypoints below. They are from the Timetrack for the "Vertices" of an Calque de Contour.

Image:Waypoints-undefined.png

You'll see the left side of each of the Waypoints is colored. This means the "In" interpolation for each vertex is the same. However, the right side is grey, indicating that the "Out" interpolation for each vertex differs.

TODO: rewrite the above so it doesn't hurt the brain so much.

Example combining Waypoints

Ease in - Normal - Ease out

Image:Waypoint - ease in-out.png

Futur things ?

 Interested in futur things ? [voir lien page anglaise Waypoints ... what could be the future of...? ] in the synfig forum.


Languages Language: 

English • suomi • français